Rheem Furnace Repair Nationwide | Dalton Heating & Air Fort Lauderdale

Rheem Furnace Repair in Fort Lauderdale: What to Know First

Rheem furnace repair in Fort Lauderdale with Dalton Heating & Air runs $150 – $700 for most jobs, with an honest diagnosis before any part gets ordered or replaced. We’re an independent Rheem service provider, which means we can repair what’s broken using the part that makes sense for your budget, without being tied to a manufacturer playbook. If your Rheem furnace is acting up, call (754) 354-6972 and a real person will pick up.

Call (754) 354-6972

This page is written for homeowners in Fort Lauderdale who own a Rheem furnace and want to know what’s wrong, what it costs to fix, and whether the repair actually makes sense. Marco Benitez runs our Fort Lauderdale operation. His crews know Rheem’s gas valves, ignitors, and control boards well enough to tell you the cause, the price, and the repair plan before anything gets opened up.

How Rheem Products Fail – and How We Fix Them

• Rheem 80% AFUE single-stage furnaces: hot-surface ignitor failures. This is the most common no-heat call we see on Rheem’s entry-level line in Fort Lauderdale homes. These ignitors are silicon carbide, and they crack from years of thermal cycling, especially in houses near the coast where salt air puts a little extra stress on all electrical connections. When the ignitor cracks, the gas valve opens but nothing lights. We replace with a nitride ignitor where the model allows it, which holds up much longer.
• Rheem Classic 90 Plus: pressure switch trips on humid nights. Fort Lauderdale’s humidity plus a partially blocked condensate drain or a stretched inducer motor means the pressure switch never closes, the board refuses ignition, and the furnace throws a code. Our fix isn’t just swapping the switch. We clean the condensate trap, check the inducer draft, and verify the switch trips at the right inches of water column before calling it done.
• Rheem Prestige series: gas valve solenoid failure after 7 – 10 years. The Prestige line uses multi-stage gas valves, and the low-fire solenoid tends to go first. The furnace will still run on high fire, so the homeowner doesn’t notice until the gas bill climbs or the rollout limit trips. We test both stages under load, confirm the manifold pressure in inches of water column, and replace with either an OEM Rheem gas valve or a Siemens equivalent, whichever your budget and warranty situation favors.
• Rheem Classic Series: induced draft motor bearing wear. These are actually pretty stout motors, but in Fort Lauderdale they run less than northern units, and moisture from extended off-cycles shortens bearing life. The motor starts squealing on startup. We’ll open the assembly and tell you whether the bearings can be re-lubed or whether the motor needs replacement. No guesswork, no unnecessary part swap.
• Rheem condensing units: condensate leaks onto control boards. Condensing Rheem furnaces produce acidic water as a byproduct. If that water leaks past the collector box gasket, it drips onto the control board and the furnace starts throwing random lockout codes. Many techs replace the board and call it fixed. We replace the gasket, clean the trap, then test the board. That’s the difference between a repair that lasts a year and a repair that lasts.

Our Rheem Furnace Repair Process

Here’s what a Rheem furnace repair looks like when you call Dalton Heating & Air Fort Lauderdale:

1. 1
   You call (754) 354-6972. A live person answers, asks for your address, and gets you a window that same day.
2. 2
   Our tech arrives inside the window. Uniform, background-checked, and with Rheem-specific diagnostic tools in the truck, not just a generic meter.
3. 3
   We diagnose the furnace, not just the symptom. The tech verifies the sequence of operation: inducer, pressure switch, ignitor, flame sensor, gas valve. Each step tested and confirmed.
4. 4
   You get a written price before any wrench turns. We tell you the part, whether it’s OEM Rheem or a quality equivalent, and the total installed price. You approve it or we don’t do the work. No surprise line items.
5. 5
   We repair, test, and clean up. The tech runs the furnace through a full cycle, checks manifold pressure with a manometer, verifies no gas leaks at the union, and wipes down the cabinet.
6. 6
   You get the guarantee in writing. Every repair is covered for a full year under the 365-Day Done Right Promise. If the repair fails in that time, we return at no charge.

What Rheem Furnace Repair Costs in Fort Lauderdale

Most Rheem furnace repairs in Fort Lauderdale fall between $150 and $700 depending on the part. The actual number comes down to what failed and what’s worth replacing.

A hot-surface ignitor replacement typically runs at the low end of that range. A gas valve on a Prestige series will push toward the top. A heat exchanger repair, if it’s even safe to attempt, can exceed $700, and at that point we’ll show you the numbers and let you decide whether replacement makes more sense than pouring money into a 12-year-old furnace. There’s no markup games, no “while we’re here” upsell. The written estimate is the price you pay.

Call (754) 354-6972 for a free estimate. You’ll get the exact number for your specific Rheem model before you commit to anything.

Why Fort Lauderdale Homeowners Call Dalton Heating & Air Fort Lauderdale for Rheem Work

Most of our Fort Lauderdale Rheem customers came to us after a previous company didn’t show up, quoted one price and charged another, or left a mess on the floor. We operate under The Garrison Standard, which has been in place since 2003. That means the price is in writing before any work starts, the technician arrives inside the stated window, and every repair carries a written one-year guarantee. If the repair fails, the second visit is free. That’s not a promotional offer. It’s how we’ve operated for over two decades.

Our techs work on Rheem furnaces weekly, not occasionally. They know which boards throw which codes, which gas valves fail on which series, and when a part should be OEM Rheem versus a quality aftermarket equivalent. And if your Rheem is too far gone and you’re ready for another brand, we also service and install Carrier, Trane, and Lennox. We’ll give you the straight comparison without any bias toward whichever pays us more.

FAQs